Renseignements généraux

Nº de série

5918

Nº de partie

1

Nombre total de parties

2

Ou

S/O

Brevets

S/O

Description générale

.1 METAL, INCLUDING IRON & BRASS/.2 METAL, INCLUDING IRON, COPPER & BRASS; SYNTHETIC CORD

Dimensions

Remarque : Cette information reflète la taille générale pour l’entreposage et ne représente pas nécessairement les véritables dimensions de l’objet.

Longueur

18,5 cm

Largeur

17,5 cm

Hauteur

30,0 cm

Épaisseur

S/O

Poids

S/O

Diamètre

S/O

Volume

S/O

Lexique

Groupe

Technologie industrielle

Catégorie

Sources d'énergie

Sous-catégorie

S/O

Fabricant

Ou

Devilbiss

Pays

Inconnu

État/province

Inconnu

Ville

Inconnu

Contexte

Pays

Inconnu

État/province

Inconnu

Période

Inconnu

Canada

Inconnu

Fonction

TO PLACE & HOLD AIR OR ANOTHER GAS UNDER PRESSURE SO THAT IT CAN BE USED AS A POWER SOURCE.

Technique

Inconnu

Notes sur la région

Inconnu

Détails

Marques

.1 PLATE 'DEVILBISS (CAN.) LTD./ BARRIE, ONT./ MOD. NO. 120A/ SER. NO. 5918/ LUBRICATION UP TO 100o F./ S.A.E. -10W/ OVER 100o F./ S.A.E. -20'/.2 LABEL 'DEVILBISS [LOGO FORM] DE/ V'/ PLATE 'DEVILBISS (CANADA) LTD./ BARRIE, ONTARIO/ MODEL SERIAL NO. MAX. OPER. PRES./ UBHB-5010 831260 60/ CAUTION: THIS MACHINE WHEN USED FOR PAINTS, LACQUERS OR VOLATILE SPRAYS/ MUST NOT BE LOCATED IN SPRAY BOOTHS OR CONFINED AREAS./ THIS MACHINE SHALL BE MOUNTED AGAINST A WALL WHEN NOT/ PROVIDED WITH A BELT GUARD. NOT CLOSER THAN 12 INCHES./ FOR PARTS AND SERVICE, ALWAYS GIVE MODEL AND SERIAL NUMBER.'/ ON GAUGE 'U.S. GAUGE' & MK'D OFF '0' TO '300'/ "IMPORTANT SERVICE INSTRUCTIONS/ 1. THIS EQUIPMENT IS SHIPPED WITHOUT OIL. FOLLOW LUBRICATING INSTRUCTIONS BEFORE STARTING./ 2. INSTALL OR USE IN A CLEAN LOCATION AWAY FROM DUST AND FUMES./ 3. EQUIPMENT SHOULD BE LEVEL FOR BEST OPERATION IN PERMANENT INSTALLATION SHIM AIR RECEIVER FEET TO ELIMINATE STRAIN./ 4. FLYWHEEL MUST BE AT LEAST ONE FOOT FROM WALL AND TOWARD THE WALL FOR SAFETY./ 5. FAN TYPE FLYWHEEL MUST ROTATE SO AS TO BLOW AIR TOWARD COMPRESSOR./ 6. ELECTRIC MOTORS MUST HAVE ADEQUATE OVERLOAD PROTECTION PROVIDED./ 7. PREVENTATIVE MAINTENANCE - SEE SERVICE LITERATURE."/ "ELECTRICAL INSTRUCTIONS/ UNLESS PROPER SIZE WIRING IS USED AND OVER-/ LOAD PROTECTION IS PROVIDED, THE MANUFACTURER/ OF THIS EQUIPMENT WILL NOT BE RESPONSIBLE FOR ANY/ MOTOR FAILURE DUE TO IMPROPER FUNCTIONING OF THIS/ UNIT./ DUAL VOLTAGE MOTORS - SINGLE PHASE UP TO AND IN-/ CLUDING 3/4 H.P. - WIRED AS INDICATED BY CUSTOMER/ ORDERS./ POLYPHASE NOT WIRED BY FACTORY./ IF 220 IS REQUIRED INSTEAD OF 110 OR 110 IN PLACE OF 220/ ETC., HAVE MOTOR WIRING CHANGED BY COMPETENT/ ELECTRICIAN BEFORE EQUIPMENT IS PUT IN SERVICE./ OVERLOAD PROTECTION AND FUSES MUST BE PROVIDED/ ACCORDING TO CURRENT USED."/ ON SWITCH: "PUMPTROL/ CLASS 9013/ TYPE FORM/ FSG 3/ D [WITH SQUARE AROUND IT]/ ON OFF/ 40 60/ MAX. H.P. RATINGS/ V. 1PH 3PH D.C./ 110 1 1 1/4/ 220 1 1 1/4/ SQUARE D COMPANY/ CANADA LIMITED/ CSA".

Manque

WOULD REQUIRE A MOTOR & PULLY TO FORM A FUNCTIONING AIR COMPRESSING UNIT

Fini

.1 BLACK, SILVER COLOUR PT, BRASS COLOUR FITTING/.2 PAINTED ORANGE, MUCH CHIPPED OFF, SHOWING DARK SILVER-GREY; SWITCH BOX PAINTED GREY, OTHER PTS SILVER, BRASS & COPPER COLOURED, BLACK CORD, PRESSURE GAUGE PAINTED BLACK WITH WHITE FACE

Décoration

S/O